How to do a tape stop in Ableton Live
A tape stop slows a track down to a standstill, dropping in pitch as it goes, like a tape machine or a turntable switched off mid-song. Ableton Live has no device that does it, but there are three ways to get one. A plugin is the quickest, and the other two use Live's warping. I make simpleTapeStop, the free plugin below. The clips are a loop run through its engine.
By Aiden Shihadeh, developer of simpleTapeStop · Published
Quick answer
| Way | Works on | The catch |
|---|---|---|
| simpleTapeStop (free plugin) | Any track, group or the Main track, audio or MIDI | Needs a plugin install |
| Re-Pitch and tempo automation | Warped audio clips | Slows the whole set, so you record the result and undo it |
| Warp markers | One warped audio clip | Slow to draw, and the slowdown comes in steps |
simpleTapeStop is free with no account, for Ableton Live on Mac, Windows and Linux. Download free
simpleTapeStop is free. If you'd like to support it, you can leave a tip.
Check out my other free plugin, simpleStutter. It does stutters, half time and gates.
What a tape stop sounds like
A four-bar loop dry, then with a stop at the end of bar 2 and another over bar 4, in three shapes: a straight slowdown, a hard brake, and one that runs on into reverse.
With a tape stop plugin
This is the way I'd do it, since it works on any track and you can move the stop later without redoing anything.
- Download simpleTapeStop from its page and run the installer. On a Mac it installs AU, VST3 and CLAP, and on Windows VST3 and CLAP. Live uses the VST3, or the AU on a Mac.
- In Live's settings (Live → Settings on a Mac, Options → Settings on Windows), open the Plug-Ins tab, turn on Use VST3 Plug-In System Folders or Use Audio Units, and click Rescan.
- In the browser, click Plug-Ins, open simpleSoundbank and drag simpleTapeStop onto the track you want to stop. For the whole song, put it on the Main track.
- Set the Stop time. Turn on Sync to set it in note lengths, from 1/32 to 4 bars; half a bar is a good start. Set Start time the same way for the spin-up, and turn Curve one way for a hard brake or the other for a slow drift.
- In Arrangement View, open the track's automation, pick simpleTapeStop's Stop parameter, and draw it on where the stop should start and off where the music should come back.
Put the "off" point on a bar line and the track comes back in time. Turn on Reverse and the tape runs backwards after it stops, for a rewind.
If you want stops as part of a repeating pattern, every 4 bars for example, or mixed with stutters and half time, simpleStutter has Tape stop blocks you draw on a grid. I've compared other free tape stop plugins in free tape stop plugins.
With Re-Pitch and tempo automation
This uses Live's own warping. When a clip's warp mode is Re-Pitch, its pitch follows its speed like tape, so slowing the tempo drops its pitch too.
- For each audio clip that should stop, open Clip View and set Warp mode to Re-Pitch. A MIDI part needs bouncing to audio first, because MIDI instruments keep their pitch when the tempo changes.
- Show the Main track's automation and pick Song Tempo.
- Draw the tempo from the song's BPM down to Live's lowest tempo over the length of the stop, and bend the line so it drops faster at the end.
- Make a new audio track, set its Audio From to the track or group that's stopping, and record the passage.
- Delete the tempo automation and use the recorded clip in place of the original.
It sounds like a real slowdown, but it slows every warped clip in the set, which is why you record it and undo it. It's also hard to time the end, because the beat grid itself slows down.
With warp markers on one clip
This stops a single clip without touching the tempo.
- Set the clip's Warp mode to Re-Pitch.
- Double-click in the clip's waveform to add warp markers on each 16th of the stretch you want to stop, for example the last beat.
- Drag the markers apart so each gap is longer than the one before. Each gap now plays slower and lower than the last.
- Cut the clip where the stop ends, or fade it out there.
The slowdown comes in steps, one per gap, so you need a lot of markers for a smooth stop. It works for a short stop on a vocal or a drum loop.
Common questions
Does Ableton Live have a tape stop effect?
No. Live 12 has no tape stop device. You can make one with Re-Pitch warping and tempo automation, or with warp markers, or put a tape stop plugin on the track.
How do I tape stop only one track in Ableton?
Put a tape stop plugin on that track, or set that clip to Re-Pitch and use warp markers. Tempo automation slows every warped clip, so it suits a stop on the whole song.
How do I tape stop the whole song in Ableton?
Put a tape stop plugin on the Main track and automate its Stop parameter. Everything going through the Main track slows together, audio and MIDI.
How long should a tape stop be?
For a fill before a drop, half a beat to two beats. For the end of a section or a full power-down, one or two bars. With Sync on, simpleTapeStop sets it in note lengths so it stays in time at any tempo.
Is simpleTapeStop free?
Yes. There's no trial and no account. It's VST3, AU and CLAP on Mac, VST3 and CLAP on Windows, and VST3, CLAP and LV2 on Linux.